Ciprico Rimfire 3880 User Manual Page 214
- Page / 230
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
21020285 D User’s Guide
Appendix D Defaults
Page D - 4 Hardware Defaults
Command
Defaults
If you do nothing to change the board operation by using the available Board-
control commands, the adapter uses defaults. These are listed below. For more
information see Chapter 7.
Command Parameters Default Values Meaning
Identify
- returned in the status block
Engineering Revision XX
Depends on revision.Firmware Revision XX
Day, Month, Year XXXXXX
Options Flags = 14H
Tag bit 2 = 1 Tagged commands supported.
Reset bit 4 = 1
SCSI bus will reset at adapter reset - set by
board jumper default setting.
SCSI ID bits 0, 5, 6, 7 = 0 Set by board jumper default settings.
FW # of Even Prom XXXXXXXX Depends on revision.
General Option
- these are used if you set nothing yourself
Bus Throttle 0BH 2048 bytes per burst.
Select Flags = 03H
Disconnect/Reconnect bit 0 = 1 Allow Disconnect/Reconnect.
SCS Bus Parity bit 1 = 1 Check for SCSI parity errors.
Block Mode Transfers bit 2 = 0
Block Mode transfers depend on address
modifiers.
Unit Options and Extended Unit Options
- used if you set nothing
Disconnect Timeout 0H No timeout occurs
Retry Limit 0H No retries enabled.
Retry Control = 0H
Issue Interrupt bit 0 = 0 No interrupt on retry.
Issue Status Block bit 1 = 0 No Status Block on retry.
Retry Parity Errors bit 2 = 0 No retry for parity errors.
Retry Command Errors bit 3 = 0 No retry for device errors.
Retry Bus Errors bit 4 = 0 No retry for bus errors.
Select Timeout FAH 250 milliseconds.
Unit Flags = 0H
Untagged Queue bit 0 = 0 Send one command at a time.
Synch Negotiation bit 1 = 0 Will not initiate synchronous negotiation.
Inhibit ATN Signal bit 2 = 0 ATN will be asserted.
Wide Transfers bit 3 = 0 Will not initiate wide negotiation.
Tagged Commands bit 6 = 0 Tagged commands not negotiated.
Sense Count 08H First eight bytes of Sense Data.
Selected Sense Bytes all = 0 First eight bytes of Sense Data returned.
Board Information
- these are returned in a Data Structure
Select Flags = 03H
Disconnect/Reconnect bit 0 = 1 Allow Disconnect/Reconnect.
SCSI Bus Parity bit 1 = 1 Check for SCSI parity errors.
Block Mode Transfers bit 2 = 0
Block Mode transfers depend on address
modifiers.
Bus Throttle 0BH 2048 bytes per burst.
Table 127: Command Defaults
- Rimfire 3880 SCSI Host 1
- Organization 5
- Conventions 7
- Documents 8
- Table of 9
- Contents 9
- Product Overview 21
- About the 22
- Rimfire 3880 22
- Management 23
- What next? 24
- Hardware Essentials 25
- Structure and 27
- Description 27
- Block Diagram 28
- Addressing 29
- Ports: General 30
- Address Buffer 32
- SET 0 0 0 0 WID WSC BSC 33
- Channel 34
- Attention Port 34
- Status Port: 38
- Reset Port 40
- Descriptions of 41
- Port Usage 41
- Hardware Installation 43
- Overview of the 45
- Installation 45
- Step 1: 46
- Unpacking the 46
- Step 2: 47
- Jumpers and 47
- Termination 47
- Configuration 48
- Bus Request/ 49
- Grant Jumper 49
- Addresses 51
- SCSI bus 52
- Step 3: Board 53
- Insertion 53
- Step 4: Apply 54
- Conditions 55
- Step 5: 56
- Configure and 56
- Connect SCSI 56
- Command Operation 59
- What the 61
- Adapter must 61
- The Base 62
- Parameter 62
- Multiple 66
- Status Blocks 66
- 000 0 0 INT ID 68
- Using a Single 69
- Some Example 70
- 2:Inquiry 73
- Pass-through 73
- Command List 76
- Creating the 78
- Using a 79
- Adding a 80
- Removing a 80
- Example ‘C’ 81
- Routines for 81
- Initiator Mode Pass 85
- Initiator Pass 87
- Block Format 87
- DBV 0 ICC 0 IRS DAT DIR 0 88
- Setting DBV 89
- DAT and DIR 89
- Table Values 89
- Table of DAT 90
- Automatic 90
- Settings 90
- 21020285 D User’s Guide 102
- Target Mode Pass 103
- Introduction 104
- Overview of 105
- Target Mode 105
- What must the 106
- Target Mode? 106
- Commands 107
- Special Target 107
- Command 108
- Descriptor 108
- Block Group 108
- Operation 109
- Sequence of 111
- Responding to 111
- Selection Data 112
- Structure 112
- 76543210 113
- CC ERR RTY 0 0 0 0 TME 113
- 0000000SAV 116
- Response 117
- 0 0 ICC TMO 0 DAT DIR 0 118
- Status Block 121
- CC ERR RTY 0 0 CSB 0 TMS 122
- Board-control Commands 125
- Using the 127
- Reference 127
- General Status 128
- List of 129
- Start Command 130
- List (01H) 130
- 1514131211109876543210 131
- 0 0 0 0 0 INT Status/ID 131
- Stop Command 132
- List (02H) 132
- Identify (05H) 133
- Identify 134
- Description of 134
- Statistics (06H) 136
- Statistics Data 138
- General 139
- Options (07H) 139
- Unit Options 142
- 0 0 0 RBE RCE RPE ISB INT 143
- 0 TAG 0 0 WID IAT SYN UNQ 144
- Diagnostic/ 148
- Self-test (09H) 148
- Enable (0AH) 151
- 000 0 0 INT Status/ID 152
- Disable (0BH) 153
- Abort (0DH) 154
- SCSI Hard 155
- Reset (10H) 155
- Information 156
- Data Structure 157
- Extended 165
- Statistics (16H) 165
- Extended Unit 169
- Options (18H) 169
- Options Data 170
- Details of Usage 175
- Byte and Word 177
- Swapping 177
- How to Use 182
- How It Works 183
- Notes on 184
- Usage and 185
- SCSI Protocol 185
- Handling 185
- Routines 188
- Disconnect 189
- Privilege 189
- Error Codes 193
- User’s Guide 21020285 D 195
- Appendix A Error Codes 195
- Summary Page A - 3 195
- Table 116: Error Codes 195
- Appendix A Error Codes 196
- Page A - 4 Summary 196
- Summary Page A - 5 197
- Status Port 198
- Self-test Error 199
- Self-test 199
- Cables and Connectors 201
- Connector 203
- Table 123: P2 Connector 205
- Specifications 207
- Appendix C Specifications 210
- Page C - 4 Specifications 210
- Defaults 211
- Hardware 213
- Appendix D Defaults 216
- Design Differences 217
- Features no 219
- Supported 219
- Implementation 220
- Differences 220
- Maximize 222
- Performance 222
- Index 224
- Page ii 224
- Index 225
- Page iii 225
- Page iv 226
- Page vi 228
- 21020285 D 230
Related products and manuals for Unknown Ciprico Rimfire 3880
Unknown Ciprico 6500 User Manual
(92 pages)
(92 pages)
© 2020, manymanuals.com. All rights reserved. | 1.659 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals