Ciprico Rimfire 3880 User Manual Page 107
- Page / 230
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
User’s Guide 21020285 D
Chapter 6 Target Mode Pass-through Commands
Overview of Special Target Mode Commands Page 6 - 5
Overview of
Special Target
Mode
Commands
To implement the Target Mode described in the previous pages, three new
commands and a new type of Status Block were used. These are described
briefly next so the commands will be familiar as the Sequence of Operation is
described.
New
commands
• Target Mode Enable command
• Target Mode Disable command
• Target Mode Response command
Note
For a complete
description of the Target
Mode Enable command
and the Target Mode
Disable command, see
Chapter 7. The Target
Mode Response
command is described
fully later in this chapter.
Target Mode Enable Command
When you want the adapter to begin operating in Target Mode, you must issue
a Target Mode Enable command to the adapter. This command must be issued
after the host has set up the memory for the Target Selection Data Structure
that the adapter will use. Until this command is issued, the adapter will respond
to all selection attempts by disconnecting from the SCSI bus.
Target Mode Disable Command
The Target Mode Disable command is issued when you wish to stop receiving
selections from initiators on the SCSI bus.
Target Mode Response Command
When ready with the response for the initiator that has selected the RF3880,
use the Target Mode Response command to inform the adapter what action to
perform. Target Mode Response commands are queued in the adapter for
execution in the same way as initiator commands.
- Rimfire 3880 SCSI Host 1
- Organization 5
- Conventions 7
- Documents 8
- Table of 9
- Contents 9
- Product Overview 21
- About the 22
- Rimfire 3880 22
- Management 23
- What next? 24
- Hardware Essentials 25
- Structure and 27
- Description 27
- Block Diagram 28
- Addressing 29
- Ports: General 30
- Address Buffer 32
- SET 0 0 0 0 WID WSC BSC 33
- Channel 34
- Attention Port 34
- Status Port: 38
- Reset Port 40
- Descriptions of 41
- Port Usage 41
- Hardware Installation 43
- Overview of the 45
- Installation 45
- Step 1: 46
- Unpacking the 46
- Step 2: 47
- Jumpers and 47
- Termination 47
- Configuration 48
- Bus Request/ 49
- Grant Jumper 49
- Addresses 51
- SCSI bus 52
- Step 3: Board 53
- Insertion 53
- Step 4: Apply 54
- Conditions 55
- Step 5: 56
- Configure and 56
- Connect SCSI 56
- Command Operation 59
- What the 61
- Adapter must 61
- The Base 62
- Parameter 62
- Multiple 66
- Status Blocks 66
- 000 0 0 INT ID 68
- Using a Single 69
- Some Example 70
- 2:Inquiry 73
- Pass-through 73
- Command List 76
- Creating the 78
- Using a 79
- Adding a 80
- Removing a 80
- Example ‘C’ 81
- Routines for 81
- Initiator Mode Pass 85
- Initiator Pass 87
- Block Format 87
- DBV 0 ICC 0 IRS DAT DIR 0 88
- Setting DBV 89
- DAT and DIR 89
- Table Values 89
- Table of DAT 90
- Automatic 90
- Settings 90
- 21020285 D User’s Guide 102
- Target Mode Pass 103
- Introduction 104
- Overview of 105
- Target Mode 105
- What must the 106
- Target Mode? 106
- Commands 107
- Special Target 107
- Command 108
- Descriptor 108
- Block Group 108
- Operation 109
- Sequence of 111
- Responding to 111
- Selection Data 112
- Structure 112
- 76543210 113
- CC ERR RTY 0 0 0 0 TME 113
- 0000000SAV 116
- Response 117
- 0 0 ICC TMO 0 DAT DIR 0 118
- Status Block 121
- CC ERR RTY 0 0 CSB 0 TMS 122
- Board-control Commands 125
- Using the 127
- Reference 127
- General Status 128
- List of 129
- Start Command 130
- List (01H) 130
- 1514131211109876543210 131
- 0 0 0 0 0 INT Status/ID 131
- Stop Command 132
- List (02H) 132
- Identify (05H) 133
- Identify 134
- Description of 134
- Statistics (06H) 136
- Statistics Data 138
- General 139
- Options (07H) 139
- Unit Options 142
- 0 0 0 RBE RCE RPE ISB INT 143
- 0 TAG 0 0 WID IAT SYN UNQ 144
- Diagnostic/ 148
- Self-test (09H) 148
- Enable (0AH) 151
- 000 0 0 INT Status/ID 152
- Disable (0BH) 153
- Abort (0DH) 154
- SCSI Hard 155
- Reset (10H) 155
- Information 156
- Data Structure 157
- Extended 165
- Statistics (16H) 165
- Extended Unit 169
- Options (18H) 169
- Options Data 170
- Details of Usage 175
- Byte and Word 177
- Swapping 177
- How to Use 182
- How It Works 183
- Notes on 184
- Usage and 185
- SCSI Protocol 185
- Handling 185
- Routines 188
- Disconnect 189
- Privilege 189
- Error Codes 193
- User’s Guide 21020285 D 195
- Appendix A Error Codes 195
- Summary Page A - 3 195
- Table 116: Error Codes 195
- Appendix A Error Codes 196
- Page A - 4 Summary 196
- Summary Page A - 5 197
- Status Port 198
- Self-test Error 199
- Self-test 199
- Cables and Connectors 201
- Connector 203
- Table 123: P2 Connector 205
- Specifications 207
- Appendix C Specifications 210
- Page C - 4 Specifications 210
- Defaults 211
- Hardware 213
- Appendix D Defaults 216
- Design Differences 217
- Features no 219
- Supported 219
- Implementation 220
- Differences 220
- Maximize 222
- Performance 222
- Index 224
- Page ii 224
- Index 225
- Page iii 225
- Page iv 226
- Page vi 228
- 21020285 D 230
Related products and manuals for Unknown Ciprico Rimfire 3880
Unknown Ciprico 6500 User Manual
(92 pages)
(92 pages)
© 2020, manymanuals.com. All rights reserved. | 0.693 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals